Give each person their own playback device and headphones. Set the meeting app's speaker and microphone on the caller's device. Then select the listener's headphones as the music destination on their phone or tablet. Test the call and music separately, then together. The setup passes when both people hear their own audio and neither stream comes out of a shared speaker.
This workflow is for two people using two source devices in the same space. Each person can change a route without touching the other's device. A shared soundbar, monitor speaker, or portable speaker can remain nearby. Treat it as an output that both people should check for accidental playback.
Assign two independent audio routes
Decide which device runs the video meeting and which device plays music. Give the caller a headset with a microphone and the listener a separate pair of headphones or earbuds. Write the route in plain language. One example is “laptop meeting to USB headset” and “phone music to earbuds.” The meeting microphone is an input on the laptop, so list it separately.
Set both devices to a comfortable test volume before starting. If the two headsets have similar Bluetooth names, check which one is actually connected to each source. Keep your usual paired devices saved unless a specific reconnection causes trouble. The goal is to identify and control each route, which may only require selecting the right output once.
Where convenient, a wired headset on the call side leaves fewer devices competing for wireless connections. Bluetooth can also work for both people. Check the particular routes you set up. A call path that was fine yesterday may use a different default after an accessory goes to sleep.
Set the meeting output and microphone explicitly
On the caller's device, open the meeting app's audio settings or pre-join controls. Select the call headset for speaker output and its mic, or the mic you intentionally want to use, as input. In Microsoft Support's guide to Teams meeting audio, the speaker and microphone are separate choices. Use the corresponding controls in your actual meeting app. A browser may also need access to the mic you selected.
Play the app's test sound or arrange a brief test with a willing participant. Confirm that you hear a voice through the headset and the participant hears you through the intended microphone. If a test-call feature is available, use it before the actual meeting. Keep other audio paused for this first pass so you can tell what the app is sending.
If the call appears on the shared speaker, check both the meeting app and the device's current output. Some apps follow the system default, while others keep a device selection of their own. Explicitly choose the call headset again. Verify the microphone separately, since the laptop's room mic might still be active even after you moved the speaker output to the headset.
Set the personal music destination on the second device
On the listener's device, start a familiar quiet track and open its audio destination control. Choose the listener's headphones while the track is playing. On an iPhone, the playback destination control for Bluetooth accessories is available during playback. The exact picker depends on the phone and app. Check the device name alongside what you can actually hear.
Pause the track and resume once. Verify the output after a brief interruption such as locking and unlocking the phone, if that is part of normal use. If you know that going out of range can send playback back to the phone, pause first. Test reconnection at low volume, with the call still on hold or in its test stage.
If the listener has used the room speaker before, it may reconnect or remain selected. Switch the active route back to the headphones. If a particular shared speaker repeatedly grabs the route, disconnect it on the affected source when you need private listening. Keep the changes narrow so the other person can continue using their device.
Run a two-person check at the intended seats
Put both people where they will actually sit. Run the call test and the music sample together. Ask the caller whether they hear the other participant clearly and the listener whether the song remains in their headphones. Listen for leakage from the room speaker, monitor or phone. Ask a remote participant if they hear the other person's music or nearby conversation.
A wrong route and an open microphone are different observations. If the room speaker stays quiet but the remote participant still hears music, lower headphone leakage, increase the distance between seats, or move the mic closer to the caller according to its instructions. Keep the caller muted while listening only when that fits the call. If the room speaker actually emits audio, return to the device whose test sound you heard and fix its output.
Use two short signals you can tell apart. For example, the caller plays a brief meeting test tone, then the listener starts a few seconds of a familiar instrumental track. If the room speaker sounds during only one signal, you have identified the source to inspect. After fixing that route, play both together at the same volume. This sequence is easier to interpret than starting two similar voices at once.
Microsoft Support describes how supported Windows 11 and LE Audio combinations can affect playback quality while a microphone is active. Treat that as a call-device quality setting after you establish the routes. It cannot keep someone else's phone music away from a shared speaker. A reliable two-device setup works with documented wired or wireless outputs.
Keep the shared speaker available for a deliberate handoff
A shared speaker can still serve the room after the call or at another agreed time. Make that a separate action. If you plan to return to room listening afterward, use these shared-room speaker placement and listening checks to keep the sound near the people who want to hear it.
For example, the Divoom Tiivoo-2 lists a Bluetooth music source. It can be the named shared-room speaker in the handoff. During the two-person check, leave it unselected for both streams and watch for accidental playback. After the meeting ends, select it on the one device that should use it. Check the documented input and device names if you use another product from the smart pixel speaker collection.
Divoom Tiivoo-2 Retro Pixel Bluetooth Speaker with Photo Album Display
Divoom Tiivoo-2 retro pixel Bluetooth speaker with photo album display, FM radio, alarm, and app-controlled pixel art.
€46,00 EUR
€92,95 EUR
with code BF26TIV
Buy now
When you finish, both people should be able to say which source, speaker or headphones and mic are active. Repeat the check after a headset replacement or when a source starts sending sound to a different room device.
Make the handoff predictable if people swap seats during the day. Have the outgoing caller end the test and disconnect the headset only after audio is paused. The next person selects their own device and verifies the destination before resuming. This avoids a room speaker briefly picking up a stream when one pair of headphones disappears.
FAQs About Separating a Video Call and Personal Music
Can both people use wireless headphones?
Yes, when each source is connected to its own headset. Verify each destination by listening before starting both streams together.
What if the remote participant hears music but we hear no room speaker?
Check what the call microphone picks up. Move the listener farther away, reduce leakage and repeat the test with the intended microphone selected.
What if the meeting sounds fine until I turn the microphone on?
Check the selected mic and headset again. On supported Windows Bluetooth combinations, audio format with the mic active can affect quality. Your two playback destinations still need their own check.
Should I delete the shared speaker from both devices?
Usually you can leave it saved and choose a different active output. Disconnect it from a source if it repeatedly takes over during the check.
What happens if one headset disconnects during the meeting?
Pause or mute the affected stream as appropriate, reconnect the intended headset and verify the output before resuming. Some sources can fall back to built-in speakers.
Conclusion
Assign one source and one listening device to each person, and select the meeting microphone separately. Test each route and then run both at the intended seats. Keep the shared speaker for a deliberate handoff after you confirm that neither private stream is reaching it.
