Compare adapter A and adapter B using the same compatible cable, wall outlet, device charging port and device state. Run the known-good adapter first, try the other one, then return to the first. Record actual connect and disconnect events separately from a steady charging icon with a slow battery increase. A repeatable difference points to the second adapter or its interaction with this setup. It cannot by itself distinguish a compatibility issue from an adapter fault.
Decide whether the second adapter is safe to compare
Use only adapters that the device manufacturer permits and that are intact. Stop using a unit with a damaged case or plug, a burning smell, visible arcing, or unusual heat. If an outlet is loose, discolored or damaged, skip it. Unplug equipment only if you can do so safely. A suspicious electrical condition is a reason to stop and seek support, rather than reproduce the interruption. Do not open either adapter, shim a loose plug or test while a connector is under strain.
Use the labels and the device maker's requirements to choose the port on each charger. Both adapters need to support the device's intended charging method. USB-IF explains the role of USB Power Delivery in supplying power across compatible devices. A USB-C shape or a high advertised maximum does not establish that a particular port offers what the device needs. Read each port's output ratings. The guide to reading voltage, current and wattage on a USB-C label shows how to read the combinations without treating the total printed on the box as a per-port rating.
Keep the rest of the charging chain the same
Pick the cable that works with adapter A if it is suitable for both adapters and meets the device's requirements. Leave its device end in the same charging port if the manufacturer's procedure allows it. Swap only the wall adapter. Use one sound wall outlet, with no hub, monitor, dock or extension in the path. On multiport adapters, leave the other ports empty throughout this comparison. If the adapters require different cable types or connection arrangements, record that the comparison changes the adapter and cable together. It will not isolate the adapter alone.
Start at a moderate charge level, away from a known charge limit and from any temperature warning. Put the device in the same state for each pass. A phone can sit locked with its screen off, waking briefly at the same points to check status. A laptop can stay awake and idle with the same apps closed. Leave important battery settings in place and select a starting level that avoids the configured limit. Microsoft's slow or discharging PC troubleshooting distinguishes inadequate supply and load from a compatible charging setup. A battery that gains little while doing heavy work may still have a steady electrical connection.
Run A, then B, then A again
Choose an observation window long enough to cover the behavior you normally notice. Use the same length for each pass. If the device usually disconnects after a couple of minutes, a five-minute window could be a useful start. Give each adapter the same brief settling time after connection. Note the initial charging indication, any later disconnect and reconnect messages, and whether the state stays stable after the device settles. Log the start and end battery level as context, since a coarse percentage display can miss small changes.
| Pass | What stays the same | What to record |
|---|---|---|
| A first | Device, cable, port, outlet, load and observation window | Baseline charging indication and any losses |
| B | Same setup with the other compatible adapter | When any disconnect starts and whether it resumes |
| A again | Original adapter in the same setup | Whether the baseline returns |
If charge level or device temperature has moved substantially, pause until you can compare under similar conditions. A first pass starting cool and a later pass starting after sustained use can create a misleading adapter difference. With a laptop, the Surface USB-C support page is an example of model-specific advice about matching PD wattage. Use the specifications for the device you are actually testing.
A useful log has a column for the device state and one for observed events. Write “screen locked, first loss after two minutes, then resumed” instead of just “B bad.” Note any unexpected change such as a background update, an alert about temperature, or a loose-feeling connection. Those observations help distinguish a run worth repeating from one with changed conditions. If the result depends on whether the device is idle, write that as a condition and run another comparison only if the equipment is safe and the device maker permits the intended load.
If there are no disconnect events but both adapters barely increase the battery level, the intermittent symptom has not appeared. Keep that result as a separate observation about charging rate. Use a consistent, supported test under comparable load if you need to investigate the rate.
If adapter A is already the unit you use every day, label it clearly before the first pass. Near-identical housings are easy to swap accidentally. A removable note beside each charger is enough. Leave rating labels and ventilation clear. Record which wall socket you used if there are two sockets in the same plate, since moving to the other one would change the test.
Read the pattern before changing a second variable
If B repeatedly loses charging while both A passes remain steady, the result follows B in this setup. Recheck B's selected port and advertised output against the device manual. Record its model, the cable, and the observed status for support. A mismatch can look like a failure. If both adapters lose charging, check what they share: the cable, device port, outlet, and device state. Try one permitted substitute at a time, starting with a known-good cable that meets the requirements. If neither loses charging during the test, note the conditions. A short idle check can miss a problem that happens only under load.
With a Divoom Dipow 35W from the chargers and power accessories collection, the comparison still starts with a single documented USB-C output and a device whose requirements it meets. Check the rating for that port and use the device's charging state as your record. The charger's display is supplemental. A change after plugging a second device into a multiport charger calls for a separate test. Keep the second device out of this one so a new load cannot account for the result.
Divoom Dipow 35W GaN Snellader met Pixel Display Divoom Dipow 35W compact fast charger with USB-C PD and USB-A ports. Quick charge your phone, tablet, and Divoom devices safely and efficiently at home. €33,95 EUR Buy now
FAQs About Charging Interruptions With One Adapter
Does a charging icon prove the battery is filling?
It shows the state reported by the device. A steady icon and a flat percentage over a short period can reflect a small net gain, a charge limit or device load. Record both observations separately.
Is a brief message right at plug-in a disconnect?
Start timing after the same short settling period on each pass. A single initial change is different from repeated losses after charging has stabilized.
What if the interruption happens when I touch the cable?
Stop moving the connector to reproduce it. Inspect for damage while disconnected and use a compatible known-good cable if everything looks intact. A result that follows movement calls for a connector or cable check.
Can I compare adapters with different output ratings?
Yes, if each is supported for the device and the selected port meets its requirement. The test compares stability in this configuration. It does not make their speed or capacity equivalent.
What if the adapter works with a different phone?
That is useful context for support. Another device can request different power or use a different charging method, so repeat the controlled check with the original device before deciding what the result means.
Conclusion
Save the A–B–A log with the actual port and cable. If the interruption follows B while the baseline returns, take that specific combination and symptom to the manufacturer instead of replacing the other components by guesswork.
