Divoom precision manufacturing

Why Karaoke P and B Sounds Can Hit the Mic Harder Than the Rest of a Word

Written by Divoom Professional Team

Updated on

P and B can hit a karaoke microphone harder because they release a short burst of air. When the mic is close and directly in that airflow, the burst can produce a low pop that stands out from the rest of the word. A strong peak can also overload a stage of the audio chain. Moving slightly out of the breath path and lowering input level answer different questions, so try them one at a time.

A Brief Air Pulse Reaches the Grille

Both P and B are produced by briefly closing the lips and releasing them. That release can send an air pulse toward a close microphone. A mic intended for vocals can reproduce the word clearly while also reacting strongly to the sudden pressure disturbance at the grille. A built-in windscreen or foam can help reduce it. The amount you hear depends on the breath, distance, angle and design of the microphone.

Shure describes positioning the microphone above or below the direct breath path to reduce popping from plosive consonants. That is a small change in geometry. The singer keeps a useful distance and sends the air past the capsule instead of straight at it. Try it with a short word such as “pop” and “bob.” Keep the delivery, input level, and grip as consistent as you can. A take where the low pop gets smaller suggests that airflow was part of the symptom.

A burst of breath and electrical overload can distort a plosive through different paths

The change can also alter the tone if you move too far off axis. Use the smallest move that gives a meaningful difference, and compare a vowel afterward so you can hear whether the rest of the voice still sounds right. Another way to add space is to move slightly farther from the mic. Distance changes more than the burst, including how much of the voice and room sound the capsule receives. Keep that variable steady when you're specifically testing angle.

A Large Peak Can Run Out of Headroom

A pressure pulse can make a loud but otherwise clean low pop. It can also produce a signal strong enough to overload a stage in the microphone, wireless path, input or recorder. A clipped or strained peak can sound rougher and sharper than a clean burst. You may hear similar roughness on loud vowels if the input runs out of room on ordinary peaks too.

Shure's guide to input gain and headroom describes the space between a typical signal level and a maximum usable level. The guide to microphone direction and vocal placement also shows why physical technique and gain matter for a particular mic. If the recording or speaker provides an input-level control, lower that stage a little and repeat the same phrase with the same aim. A change after lowering gain is most informative when that gain control sits before the overloaded stage.

A main speaker volume knob may sit after the place where clipping happens. Turning it down can make the damaged signal quieter without making it clean. If the system has no separate input control, try a slightly less forceful delivery at the same distance, then check angle separately. A change in only one condition gives you more information than changing mic aim, voice level and output volume together.

Repeat Short Words With One Variable at a Time

Start with a comfortable listening level and a quiet background. Hold the microphone still, say “pop” and “bob,” then compare them with “mom” or a sustained vowel at a similar delivery level. Listen to the first instant of the word and to what follows it. A brief low burst that reliably follows the P or B is a useful clue. A sharp break on a loud vowel points you toward headroom or another source of distortion.

Keep the hand still for a second set and change the angle a little. Then return to the starting angle and change the input setting if your system allows it. If a room phone recording is useful, keep the phone in the same place and play back both takes at similar listening levels. The room recording can help you hear relative differences. It can't show where an electrical stage clipped just from the final waveform.

Now stay quiet and move only a finger on the handle. A thump that follows the hand while you make no sound belongs to a different path through the microphone body. A sustained ring as you aim toward the speaker suggests an acoustic return path. The timing of the sound tells you which variable to test before you touch more settings.

Check whether the same consonant sounds different on a quiet word and on a louder phrase. A close breath pulse may pop even when you say the word softly. A setup running near its limit may sound clean on the quiet pass and rough on the louder one. If the breath move fixes one problem and a gain change fixes another, both effects may have been present. Listen again to a short phrase with the backing turned down to make the onset of each word easier to hear.

A pop filter or a windscreen affects the air before it reaches the capsule. A tone control acts on the signal later. Rolling off low frequencies can reduce the sound of a pop that made it into the signal, but it can also change the weight of the voice. Once a stage has clipped, changing tone after it cannot reconstruct the lost peak. Keep the angle correction and input check as the first comparison.

Try the chosen position with a normal breath and with the loudest line you expect to sing. A position that works during a spoken check can need a small adjustment once you perform. Keep the same microphone and return to a stable aim between phrases, especially when two singers trade the mic.

Keep the Fix Small Enough for Real Singing

Use a slight angle that lets your voice reach the mic while the breath goes past it. If you use a compatible windscreen, make sure it fits as intended and leaves you enough space from the grille. Check the result with a normal lyric line. A mic technique that makes a test word clean but makes every quiet syllable disappear will be hard to use in a song.

Ivory Songbird-HQ and two matching microphones on a living-room table

The Divoom Songbird-HQ includes two matching wireless mics. With a setup like this, try the same short phrase on each at the same setting before assuming one mic is defective. The product information documents the included microphones. It does not give a measured overload point for this scenario. When comparing karaoke speakers, check which vocal level controls are available on the exact model. The guide to karaoke echo and feedback can help if a tone or tail continues after the word ends.

Divoom Songbird-HQ Draagbare Karaoke Bluetooth Speaker met Dubbele Draadloze Microfoons Divoom Songbird-HQ portable karaoke Bluetooth speaker with dual wireless microphones. Home KTV sound set for singing parties, family fun, and gatherings. $179.99 USD $239.99 USD met code BF26MUSIC Buy now

FAQs About P and B Pops on Karaoke Mics

Are P and B pops always clipping?

An air burst can produce a loud low pop without clipping. If ordinary loud vowels also sound rough, try a controlled input-level comparison.

Why does moving the mic a little to one side help?

It can put the grille outside the strongest part of the air jet while keeping the microphone close enough to hear the voice.

Will lowering the speaker volume fix the recording?

It depends on where the overload happens. A volume control after the clipped stage can reduce loudness while leaving the distortion in the signal.

Is a grip thump the same thing as a breath pop?

Check the trigger. A grip thump can occur when your hand moves while you stay quiet. A plosive pop occurs with the release of air in a spoken or sung sound.

Will a windscreen help every time?

A suitable windscreen can reduce airflow hitting the capsule. Aim and distance still matter, and an already overloaded stage may need a different level setting.

Conclusion

Test breath direction and input level separately. A slight change in aim can reduce the air pulse. An earlier gain adjustment can help when a peak exceeds available headroom. Use the same short words and a still grip to hear which change helps.

Disclaimer: This content is for general information only and is not professional or medical advice, a safety guarantee, or permission to use third-party intellectual property. Follow official product instructions and obtain any required permissions before attempting DIY projects or modifications.

Editor's Recommendation