Leave the phone in one marked position and move the speaker between two marked placements. Use the same track excerpt, volume, phone orientation and measurement window each time. Compare the same sound-level metric from both runs. The result tells you which placement reads higher at that one receiving point under the conditions you tested.
A repeatable reading requires a repeatable setup. If the phone moves, rotates or changes measurement modes, you have changed the receiving end as well as the speaker position.
Mark the receiving point and lock the phone setup
Choose the place where you actually want to compare the sound, such as the middle of your usual chair. Set the phone on a stable stand at a useful listening height. Mark the stand’s location and note the phone’s direction. Keep the same case, microphone configuration and nearby objects for every reading. Avoid holding the phone, which can change its position or partially block its microphone.
Check that the sound-level app uses the same input in both runs. Where the app supports it, select one integration metric for the whole test. CDC/NIOSH documents the iOS Sound Level Meter app and lists equivalent average measures such as LAeq alongside maximum and peak measures. For an ordinary placement comparison, use the same metric, weighting and duration in every run. A peak and a time average answer different questions.
Write down the two possible speaker positions before testing. If the question is about location, aim the speaker consistently toward the receiving point and describe the angle. If you intend to change both location and aim, call them two setups in your notes. That makes clear what the comparison can show.
Keep the source and sampling window the same
Use one known excerpt and note its start time. Choose an excerpt with reasonably repeatable content rather than comparing different songs. Disable a setting that might change the playback level between runs if you know it is active. Keep the source and speaker volume fixed, and let the setup settle before starting each reading.
Use the same measurement window, such as the same 20-second segment of your chosen track. Reset or start a new measurement for each pass according to the app. The NIOSH app guide explains the displayed metrics and controls. Stop each run at the same elapsed time. Avoid including different lengths of quiet before or after the excerpt.
Hold the room conditions steady where possible. A conversation, an opening door or a ventilation change can alter the result. Check the background before the first run and repeat a run when an obvious outside sound intrudes. Keep playback at an ordinary, comfortable level.
Start each measurement the same way. You might reset the reading while the track is paused, cue the known timestamp, and begin collecting at the first beat. If two people help, have one person run the source and the other watch the measurement without touching the stand. A shared start cue reduces variation between passes.
Measure placement A, then placement B, then return to A
Play the selected excerpt with the speaker in position A and write down the chosen reading. Move only the speaker to position B and repeat the excerpt and window. Then return the speaker to its original marks and run the same measurement again. The return pass helps reveal whether the setup drifted while you were testing.
Compare the two A readings first. If they differ about as much as the A-to-B comparison, treat the placement result as uncertain. Repeat under steadier conditions. If both A readings are similar and B is consistently higher, you have useful evidence for that point and excerpt.
For example, imagine the first A pass reads 61 and the return to A reads 64 using the same metric. A B pass of 63 would fall between those observations, so the result would not establish a repeatable placement difference. Treat those numbers as an illustration of the decision, not a threshold for your phone or room.
Write down the order, each result and any unusual background noise. A change at the phone can come from direct sound, reflections or the room’s response. The Genelec placement guidance explains why speaker and listener position affect what reaches one point. It provides useful context for interpreting the comparison without predicting a universal result for your room.
If you are unsure whether the order affected the outcome, repeat the sequence in the reverse direction under the same conditions. Check whether the difference persists when B comes first. Keep those readings separate in the log until you have confirmed that the setup is repeatable.
Read the result within its actual limits
A higher number at one chair says little about another corner of the room. It also says little about which placement sounds more balanced. Use the reading for the question you set out to answer, then listen for changes in tone or clarity separately. If those sound different with nearly identical average readings, keep both observations.
For instance, one placement can make a bass passage seem fuller while a spoken section becomes less clear. Use the same excerpt to check each impression from the fixed seat. If you choose a placement based on intelligibility, record that reason alongside the level result so someone can reproduce the decision.
When you want to know where a room is loudest, use a separate set of measurements across marked receiving points. Keep the source and window fixed for that survey. Do not reuse a single-point A/B result as a room map or exposure assessment. In a casual comparison, the same phone and setup are useful for a relative result. Absolute or compliance measurements require an appropriate method and equipment.
If you hear a physical buzz that changes between surfaces, try this speaker and shelf rattle comparison as a separate check. A vibrating shelf can change what reaches the phone, and a controlled listening test can help identify the source of that difference.
Keep the same playback mode on the actual speaker
Check that the speaker stays on the same input as you move it. A reconnect, volume reset or mode change can invalidate the pass. Use a surface that supports the speaker and leaves the intended output unobstructed.
The Divoom Tiivoo-2 documents Bluetooth as one music input. If you use it, verify the same source and level after relocating it. For another model in the smart pixel speaker collection, check its volume behavior and input controls before running the comparison. Leave the phone meter on its marked stand through the whole set.
Altoparlante Bluetooth Pixel retrò Divoom Tiivoo-2 con display per album fotografico
Divoom Tiivoo-2 retro pixel Bluetooth speaker with photo album display, FM radio, alarm, and app-controlled pixel art.
$49.99 USD
$99.99 USD
con il codice BF26TIV
Buy now
Retain the repeatable positions and the sampling settings in your notes. If you move the chair, change the track or move other furniture later, establish a new comparison for those conditions.
Check that each temporary position gives the speaker stable support and leaves the phone microphone clear. Keep tables and chairs in the same places while you move the speaker. If you swap both the table and speaker location, label the result as a comparison of two complete setups.
FAQs About Comparing Speaker Placements With a Fixed Phone
Should I hold the phone while testing?
Use a stable stand. Keep the position, orientation and height fixed throughout the comparison.
Can I compare a maximum reading with LAeq?
Use the same metric for both placements. A maximum reading and an equivalent average summarize different things.
What if the two A readings differ as much as B?
Treat the comparison as uncertain. Look for changes in background noise, timing, source level or placement and repeat.
Does a louder reading mean the placement sounds better?
It means the chosen metric was higher at the fixed point during that pass. Compare clarity and tone separately.
Will this find the loudest spot in the room?
It compares two setups from one receiving point. A room survey requires readings at several points under controlled conditions.
Conclusion
Fix the receiving point, keep the source and sampling window constant, and compare A, B and a repeat of A. Record the outcome as a relative reading for that seat and those conditions. Use a separate survey if your question involves the rest of the room.
