A pre-fader send takes a copy of a channel's signal before that channel's fader. On a karaoke mixer with an independent monitor send, the singer can keep hearing the microphone in a monitor even when you lower the microphone's channel fader in the audience mix. The monitor branch is fed from a point the main channel fader has not changed.
The routing has to be in use for that result. The channel must be sent to the auxiliary mix, the auxiliary output must feed a separate monitor path, and that path needs its own level. A mixer with only one combined output cannot create an independent monitor mix simply because a control has a similar name.
One channel can feed the room and a separate monitor mix
Imagine a singer's mic arriving at a mixer input. After the input stage, its signal can go toward the main mix and also into an auxiliary bus, where it joins whatever else has been sent there. The main branch has the channel fader. The auxiliary branch has its own send amount. If that branch takes its signal before the channel fader, moving the fader changes only the level contributed through the main branch.
Yamaha distinguishes pre-fader and post-fader auxiliary sends by where each takes its signal. It describes pre-fader sends as useful for monitor mixes and post-fader sends as useful when a path should follow changes to the main channel level. The label refers to the channel fader, so start by identifying which channel and which auxiliary bus the control affects.
In an example where the vocal fader is lowered by 10 dB, the main mix receives less vocal from that channel. A monitor fed exclusively from the pre-fader aux can keep the same vocal contribution if the aux amount, master and earlier parts of the chain remain unchanged. The singer might still hear the main speakers spill into the room at a lower level. That acoustic change does not mean the aux feed changed.
The send amount and aux master still control the monitor
A channel's send setting controls how much of that channel goes into a particular auxiliary bus. If the singer wants more vocal but the backing track is already loud in the monitor, change the vocal send within that bus. The aux master can change the total output of the bus, including all of the sources mixed into it. The input gain is earlier in the chain and can affect both branches, so it is not the same adjustment.
Yamaha's live sound setup example shows how different aux sends can provide performer mixes independently of the main output. On a digital mixer, the same row of physical faders may control the main mix on one screen and sends to the selected aux bus on another. Check the displayed mode before moving a fader. The control under your hand may be acting as the send level rather than as the channel's main fader.
Mute and channel processing depend on where the mixer taps the signal. A pre-fader send may be before or after EQ, and the channel mute may or may not affect it. Yamaha's TF series documentation gives an example of selectable pre-EQ and pre-fader tap points. That is a model-specific example of why the word pre alone does not tell you what happens to every control.
Suppose the backing track is too loud for the singer but fine for the room. On a separate monitor bus, lower the track's send and keep the room fader in place. If the singer wants the whole monitor quieter, use the aux master instead. These changes have different results even when the same pair of sources is feeding both mixes.
A post-fader send follows the channel fader
If you lower the main channel fader and an aux path is post-fader, the signal feeding that send typically falls as well. That is often useful for an effects feed. When a singer's direct voice gets quieter, the signal feeding an external reverb can also get quieter. The effects return brings the processed signal back into a mix, and the return can have its own level.
An existing reverb tail can continue for a moment after the vocal fader comes down. That is sound already in the effect, not necessarily evidence that the send is still receiving the same vocal level. Our article on karaoke echo, reverb and feedback describes why tails and feedback have different causes. When checking an aux path, listen to a new spoken phrase after the fader move.
A headphone output also does not prove the mixer has a separate pre-fader aux mix. Some headphones mirror the main mix. A pre-fader listen button may solo an input for checking level without setting up a permanent singer monitor. Use the manual's signal flow and the output label to identify the actual destination.
Verify which output you are listening to before moving the fader
Start at a low level. Identify the microphone channel, main mix and candidate aux output. If the mixer and connected equipment support a separate monitor, send a small amount of vocal to it, keep the send setting fixed and listen to a short phrase while the main channel fader moves. Check the room and monitor separately so the sound from one speaker does not mask the other. Then return the fader to its prior position.
An integrated system such as the Divoom Songbird-HQ supplies a karaoke speaker and two wireless microphones. That product example belongs to a different setup from the external mixer in the diagram. Its documented mic pairing does not imply independent aux routing. Before adding a separate monitor to a karaoke setup, verify that the actual mixer has a pre-fader send and a suitable independent output.
Divoom Songbird-HQ Alto-falante Bluetooth Portátil para Karaokê com Dois Microfones Sem Fio
Divoom Songbird-HQ portable karaoke Bluetooth speaker with dual wireless microphones. Home KTV sound set for singing parties, family fun, and gatherings.
$179.99 USD
$239.99 USD
com o código BF26MUSIC
Buy now
If lowering the channel fader makes the main voice quieter while the selected monitor feed stays steady, you have verified the behavior under those settings. If both change, check whether you moved the send fader in a different mode, selected a post-fader tap or listened to an output that was following the main mix.
Document the routing if the mixer will be used again. A note that says the singer listens to Aux 1, with the vocal send set to Pre, is more useful than a note that merely says the mic is in the monitor. It tells the next person which level to change and which output to listen to during a check.
If the monitor carries several voices, confirm the test using only one known channel first. Leave the aux master steady and move that channel fader alone. Testing the stereo master instead can tell you that the audience output is quieter, but it does not identify where the aux taps the channel.
FAQs About Pre-Fader Sends on Karaoke Mixers
Why does the singer still hear the mic when I lower the main channel fader?
The monitor may be fed by a pre-fader aux send. It takes its signal before the main channel fader, so the send can stay at its previous level.
Which control turns down the mic in the monitor only?
Use that channel's send amount for the monitor bus. Its aux master usually changes all sources in the monitor mix together.
Does pre-fader mean the channel mute is bypassed?
Not always. Mute and EQ depend on the mixer design and the selected tap point. Check the signal flow for that bus.
When would I use post-fader instead?
Use it when the send should follow the main channel level, as is common for reverb or delay feeds.
Does every karaoke speaker have a pre-fader send?
No. Independent routing requires a mixer with the appropriate send and a way to deliver it to a separate output.
Conclusion
A pre-fader send branches off before the channel fader so you can set a monitor mix separately from the room. Identify the actual bus and output, then move one control and listen to each path. The result is the best way to verify how your mixer is routed.
