Divoom team discussing product support

How to Make a Three-Phrase Mic Check Before Karaoke Starts

Written by Divoom Professional Team

Updated on

Before starting the track, try three short phrases through one microphone. Say a line in your normal speaking voice, say a line with audible P and B sounds, then sing a short line at the level you expect to use. Listen for clear words, thumps and rough peaks in that order. Start low and leave enough room for the loud line without making the quiet one unintelligible.

Start with one mic and an easy listening level

Put the speaker on a stable surface and aim the microphone away from the speaker grille. Turn off the backing track. Set the microphone and output to a comfortable low starting level using the available controls. On a kit with a single microphone volume control, use it. If your system has an input gain and a separate output level, note which is which before adjusting anything. Keep your hand on the body of the mic, clear of its grille. Hold it as you expect to hold it while singing.

Ask a friend to listen from the usual seating area if someone is available. When you test by yourself, stand where you can hear the speaker without pointing the microphone at it. A clean vocal sound near the singer can still be too quiet at the listening position. The Yamaha sound check guide explains why checking the actual performing conditions is useful. Keep the second microphone switched off until the first one passes.

Try the spoken line from the same position the singer will use. A host may sound clear at a test distance even when the next singer holds the mic closer. Ask the singer to choose a comfortable distance and keep that position through the three phrases. If the listener hears most syllables but loses the quieter end, compare that same end again before moving the speaker. Keep their location and the backing setting fixed.

Use a spoken phrase to check basic clarity

Say “Can you hear me clearly?” at normal speaking level. Listen for every word and any harshness, echo or dropouts. If the entire line is absent, check power, mute, pairing and the kit’s documented microphone mode before raising the speaker volume. If only the ends of words disappear, check whether you are moving the mic while speaking. Use a repeatable distance for all three phrases. An angle or distance change during the first test can make the next result harder to interpret.

Three short phrases check word clarity, breath thumps and headroom before music.

Ask the listener to repeat the words they heard. That is a more useful check than asking only whether the mic is loud. If the phrase is audible but hollow or smeared, try a documented neutral effect setting where available. Repeat the same phrase before bringing in the next test. Leave each control in a known position so you can return to it if the loud phrase needs a different adjustment.

Use a different word with a similar consonant if you need a second check. Say “paper” and then a softer word at the same level. A thump that occurs only on the burst of air is a more specific clue than general bass in the speaker. Small changes to mic angle can preserve the voice while moving that air past the grille. Check the spoken phrase again after finding a better position.

Use a breath-heavy phrase to hear plosives

Say “Bring the blue paper,” at the same level and distance. Listen for a thump on the B and P sounds. A burst of air into the grille can make an otherwise clear mic sound boomy. For a small correction, angle the mic slightly so your breath moves past the grille while your voice still reaches it. Keep that change modest and compare the phrase again. Shure’s recording technique guide describes how microphone position and airflow affect these sounds.

If changing the angle reduces the thump, use that position for the final phrase. If the rumble happens whenever you touch the mic body, it may instead come from handling. Keep your grip still and repeat the line. On a shared microphone, show the next singer where to hold it and let them repeat the same short phrase. If words become faint when you change the angle, move slightly back toward the previous position and try again.

If the rough sound happens even at ordinary speech level, return to the first phrase and check the connection and effect setting. Then repeat the projected line once. Distortion that appears only on the highest peaks suggests a level issue, while interruptions or sudden gaps can come from the microphone link. Write down the difference before changing more than one control. If the speaker does not show input meters, the repeatable sound is the comparison.

Try one projected line and leave headroom

Sing “Here we go tonight” at the loudness you expect for the strongest line, keeping it brief and comfortable. Listen for sudden roughness or flattening. If the kit or mixer shows a peak indicator, check it at the same time. Reduce the documented input gain or microphone level if the loudest part clips. Start low again if there is a squeal and move the mic away from the speaker. A lower speaker output may make the room quieter while leaving an overloaded input unchanged. The gain staging guide discusses this distinction. Yamaha.

Once the loud line sounds clean, repeat the first spoken phrase. You want both phrases to remain intelligible. Bring in the backing track at a moderate level and check that the voice stays clear above it. If the track covers the voice, try lowering the track before raising the microphone again. Review the karaoke voice and backing-track balance steps if you need a separate volume comparison. Save a position that gives you room for the loud line without making the whole setup uncomfortable.

Use the same phrase for each microphone if you are switching between two singers. Keep the first microphone off while testing the second alone, then try both only if the kit supports that setup and you plan to use it. If the two-mic check changes the result, record which microphones were active and check that configuration separately.

Repeat the check with the kit’s actual controls

The Divoom SongBird-HQ has a Karaoke mode and microphone volume controls described in the SongBird-HQ user manual. Run the three phrases with one supported mic in that mode. If the other microphone will be used, repeat the spoken and projected phrases with it using the same speaker arrangement. Confirm the correct model through the Divoom karaoke collection if your kit has different controls.

Altavoz Bluetooth Karaoke Portátil Divoom Songbird-HQ con Doble Micrófono Inalámbrico Divoom Songbird-HQ portable karaoke Bluetooth speaker with dual wireless microphones. Home KTV sound set for singing parties, family fun, and gatherings. $179.99 USD $239.99 USD con el código BF26MUSIC Buy now

A singer checks one microphone beside a compact cream karaoke speaker.

Record the settings or take a quick photo of the controls when the setup is ready. If the next singer holds the mic farther away or projects much more loudly, repeat the projected phrase with that person before the first song. A brief repeat at the start is easier than trying to correct a large level change over a backing track.

FAQs About A Three-Phrase Karaoke Mic Check

Should the mic check use the backing track?

Start without the track so you can hear the voice and identify plosives or clipping. Bring music in after the three phrases pass, then check the balance with a short verse.

Is a breath thump the same as clipping?

A breath thump often coincides with a P or B sound and can improve with a small angle change. Clipping is more likely to appear at loud peaks. Compare the phrases separately.

How loud should the final phrase be?

Use the level you expect from the loudest comfortable line in the song. A short realistic phrase is enough. Leave room for that peak before bringing up the music.

What if the mic squeals during the check?

Lower the level or mute it and move the mic away from the speaker’s direct path. Restart at a low level when it is quiet.

Should two singers use the same mic setting?

Check each person with their own comfortable delivery. If the kit has shared controls, choose a setting that accommodates both voices and recheck the backing balance.

Conclusion

Use a spoken line for clarity, a breath-heavy line for plosives and a projected line for headroom. Make the smallest adjustment that fixes each result and repeat the spoken line before adding the backing track.

Disclaimer: This content is for general information only and is not professional or medical advice, a safety guarantee, or permission to use third-party intellectual property. Follow official product instructions and obtain any required permissions before attempting DIY projects or modifications.

Editor's Recommendation