Divoom precision manufacturing

How a Phone and a Charger Agree to Change the Supply Voltage

Written by Divoom Professional Team

Updated on

A phone and a USB Power Delivery charger change the supply voltage by exchanging messages before the charger moves its output. In a typical successful change, the phone requests an offered power setting, the charger accepts it, the charger moves the voltage, and then it sends a Power Supply Ready message. The phone uses that final status to know when it can draw power under the new agreement.

A useful distinction is between a setting the charger offers, a setting the phone has requested, and a setting the charger says is ready. Those can be three different states during one transition, even though the cable stays connected the whole time.

The charger describes what its port can supply

USB-IF describes USB Power Delivery as a way for devices to negotiate power over USB. In a common phone charging setup, the charger is the source and the phone is the sink. A USB-C port establishes its connection and basic power state, and devices that support PD can communicate over the configuration channel. The protocol messages and the actual voltage on the supply conductors are separate parts of the same system.

The source advertises capabilities that can include fixed voltage options. An illustrative charger might offer 5 volts and 9 volts at different allowed currents. That list makes 9 volts available for a request. It does not say that the phone is receiving 9 volts now. The phone can request only a compatible setting under the current source offer and the limits that apply to the connection.

An offer can change while devices are connected, for example when a source manages the power available to several ports. The sink then evaluates the available choices. A phone may also change what it asks for as its charging needs change. The decision can depend on its own battery and temperature management. The presence of a higher setting on a label does not identify which state is active at that moment.

Accept says the request was approved

Imagine the phone already has a lower-voltage contract and asks for the offered 9-volt fixed setting. The request identifies the selected offer and its relevant operating requirements. The source checks the request. If it can provide that setting, it replies Accept. The USB-IF Power Delivery compliance tests show Request, Accept and Power Supply Ready as separate messages to observe.

USB Power Delivery Request, Accept and PS_RDY across a voltage change

Accept tells the phone that the source agreed to the requested change. The source still has to make the electrical transition. A protocol analyzer could show Accept before the output voltage settles. A voltage meter alone may show the physical change without identifying which messages approved it. That is why a trace and a voltage reading answer different questions.

A source can also decline or defer a request. Do not infer that the requested voltage was delivered just because the phone sent the request. An earlier contract can still be relevant when a new request does not succeed, though resets and other protocol conditions can change the situation. Read the message sequence and the measured supply state together before drawing a conclusion from an incomplete log.

A trace may also show a GoodCRC acknowledgment in the exchange. It means a protocol message was received successfully. It does not mean the requested operating point has been accepted. If you are scanning a capture quickly, identify the request response and the later ready message instead of treating the first acknowledgment as permission to draw under the new setting.

The source signals that the new power is ready

After a successful transition, the source sends Power Supply Ready, usually shown as PS_RDY in a protocol trace. For the fixed-voltage example, the charger has moved the supply to the new operating level before sending that message. The phone can then continue operation within the new agreed conditions. The final status is what separates an approved change from one the source reports it has completed.

You can imagine four observations in order. First the old setting is in use. Next the phone asks for 9 volts and the charger approves. Then the supply moves toward the new voltage. Finally the source announces it is ready. The exact speed and shape of the voltage transition are governed by the applicable requirements and device implementation. The example does not give a time or voltage reading for a particular phone or charger.

The USB Type-C source power test specification describes transition and ready requirements, including cases for Programmable Power Supply. When the source and sink support a common PPS range, the sink can request values within that range. This is a different kind of offered setting from selecting a fixed 9-volt entry. Both illustrate why an active contract is more informative than a printed maximum wattage.

Read the status without treating it as battery voltage

The measured USB input voltage is the voltage on the charging connection. Inside the phone, the charging circuitry manages the battery separately. A 9-volt connection does not mean the cells themselves are charged at 9 volts. Similarly, the current can change with load even while the negotiated voltage stays the same.

For an everyday observation, keep the phone, cable, charger and port fixed. An appropriate compatible meter can show the input voltage after a change. A protocol trace is needed to tell which capability, Request, Accept and ready messages occurred. If you only see that the phone switched its charging icon, you have a status hint from the phone. You do not yet have evidence of a specific voltage or PD message.

The Divoom Dipow 35W is a consumer USB-C charging accessory with published output information. Its listing describes available output conditions. The observed contract depends on the attached device and the actual session. Our guide to reading voltage and current on a charger label helps identify the listed capabilities before you interpret what a live connection is doing.

Divoom Dipow 35W GaN Fast Charger with Pixel Display Divoom Dipow 35W compact fast charger with USB-C PD and USB-A ports. Quick charge your phone, tablet, and Divoom devices safely and efficiently at home. $35.99 USD $45.99 USD Buy now

Dipow 35W side, separate phone and loose USB-C cable on a charging shelf

If you compare two sessions, record whether the charger has other loads attached and whether the same cable was used. A meaningful note is “the connection was measured at about 9 volts after the phone entered this state.” Calling that reading a specific PPS request or a particular internal battery condition would require additional evidence.

A drop in current while the voltage stays steady can reflect a change in the load within the same contract. A change in offered settings after another port becomes active can prompt a new exchange. Record both observations separately. Seeing a new request is evidence of a proposed contract change, while seeing lower current alone is not.

FAQs About USB Power Delivery Voltage Changes

Does plugging in a USB-C charger immediately apply its highest voltage?

No. A higher-voltage PD setting is offered and requested under compatible conditions, then the source makes the approved transition.

Is Accept the same as Power Supply Ready?

Accept approves the request. PS_RDY reports that the source has completed the relevant power transition and is ready.

Can a phone request a different voltage without unplugging?

Yes, a compatible connection can negotiate a change during operation. What is available depends on the current source capabilities and the sink's needs.

Does a 9-volt reading prove the battery is receiving 9 volts?

No. It describes the charging connection at the measurement point. The phone's charging circuitry manages the battery voltage and current separately.

Why might a voltage change without a new cable?

The attached devices can change their agreement while the cable stays in place. Phone demand, available source capabilities and a compatible PPS session can affect the selected setting.

Conclusion

Follow the live sequence. The source offers, the phone requests, the source accepts and then reports when the new power is ready. The printed label helps you read the offer. The trace and voltage observation help you tell what actually happened.

Disclaimer: This content is for general information only and is not professional or medical advice, a safety guarantee, or permission to use third-party intellectual property. Follow official product instructions and obtain any required permissions before attempting DIY projects or modifications.

Editor's Recommendation